IRFP150 DATASHEET PDF
IRFP Transistor Datasheet, IRFP Equivalent, PDF Data Sheets. MOSFET. Parameters and Characteristics. Electronic Component Catalog. Fifth Generation HEXFETs from International Rectifier utilize advanced processing techniques to achieve extremely low on-resistance per. THE PRODUCT DESCRIBED HEREIN AND THIS DATASHEET ARE SUBJECT IRFP SiHFP ABSOLUTE MAXIMUM RATINGS (TC = 25 °C, unless.
|Published (Last):||22 November 2006|
|PDF File Size:||5.73 Mb|
|ePub File Size:||13.55 Mb|
|Price:||Free* [*Free Regsitration Required]|
First, I can not find the pinout diagram. I don’t know where drain, source and gate are. Which pin is gate and which is drain? What is the maximum supply voltage or the maximum operating voltage? Is It V too? The X axis is voltage and you can see it is limited to volts. The Y axis is current and this is limited to amps i. What this tells you is that if you could turn on and off the MOSFET in 10 us you could take amps but with a limited voltage of about 60 volts.
That’s an instantaneous power of 8. Alternatively you could withstand volts but at a reduced current of about 90 amps. That’s an instantaneous power of 9 kW. This is very much defined as a “single pulse” bottom left corner of graph i. If your pulse was 10 ms then you could withstand volts whilst taking no more than about 2.
(PDF) IRFP150 Datasheet download
Notice now that the power irrp150 during this much longer pulse is only watts. Eventually if the graph showed this detail you would find that the continuous power rating of watts means a continuous current of 1.
Or it could mean 10 amps at 16 volts or 16 amps at 10 volts etc. You can’t apply anything more than about a volt in reverse. See “Source-Drain Ratings and Characteristics” for numbers on page 2.
You have to consider allowed power dissipation and maximum current vatasheet. What will happen if you apply V on 0. The current would be amperes. And power dissipation kW. From datasheet you can see, that maximal allowed current is 42A, and power dissipation W.
When the FET is fully on, it behaves more or less like a resistor of value RdsON, which is 36 mOhm in this case, so there would be no way to have volts across it. However, if you apply Vds, and slowly raise Vgs from zero, at some point in will start to conduct and behave like a current source.
This is called “saturation” for a MOSFET, which always ties my brain into knots, since “saturation” for a bipolar is at the other end of the characteristic.
Some prefer to call this “linear mode”, since this is the dwtasheet to use when you want datssheet make a linear amplifier or a source follower with the FET. Breakdown maximum Vds applies in all modes. It is determined by the physical construction of the FET. Also, both instant and average dissipation are limited see SOA graphs which will give you a time- and Vds-dependent current limit if you don’t want to fry it. Pin assignment is buried within the mechanical drawings.
The most important rule about any data sheet is this: Never miss the small print, let alone the footnotes. Data sheets are marketing. Irfp50, it is complete. The Vdss voltage is the voltage which the current starts to flow through fet.
Home Questions Tags Users Unanswered. This is the datasheet of a mosfet and I have two issues: Thank you very much. Michael George 1, 8 34 Lead assignments are on page 8. It’s easy to get into the habit of skipping over the last pages in a datasheet with mechanical and packaging information, it’s understandable that you missed it.
To the best of my knowlodge, the only thing that is not correct in the datasheet is the way the on-resistance is declared: When dataasheet the data sheet from the manufacturer, the typeset error is not present Orfp150 vs. If there’s missing data, the datasheet doesn’t contain it.
See also this on the last page: Andy aka k 10 Thank you very much teacher Andy aka. You always answer my questions in a very helpful and informative way. I’ve learned from you a lot of dahasheet. Chupacabras 3, 2 11 When Vgs is high enough, then it will enter ohmic mode and meet its RdsON spec.
Internal diode would conduct and prevent this.
As for the pinout, you can bet on the standard one, ie GDS. Sign up or log in Sign up using Google.